Founded in 1987, Bimonthly
Supervisor:Jiangxi University Of Science And Technology
Sponsored by:Jiangxi University Of Science And Technology
Jiangxi Nonferrous Metals Society
ISSN:1674-9669
CN:36-1311/TF
CODEN YJKYA9
WANG Chunting, YE Yuwei, HU Jianmin, CHEN Hao, WANG Yongxin, LI Jinlong. Tribological performances of CrCN coatings under different deposition temperatures[J]. Nonferrous Metals Science and Engineering, 2015, 6(2): 42-47. DOI: 10.13264/j.cnki.ysjskx.2015.02.008
Citation: WANG Chunting, YE Yuwei, HU Jianmin, CHEN Hao, WANG Yongxin, LI Jinlong. Tribological performances of CrCN coatings under different deposition temperatures[J]. Nonferrous Metals Science and Engineering, 2015, 6(2): 42-47. DOI: 10.13264/j.cnki.ysjskx.2015.02.008

Tribological performances of CrCN coatings under different deposition temperatures

More Information
  • Received Date: January 17, 2015
  • Published Date: April 29, 2015
  • CrCN coatings with different deposition temperatures (150℃、250℃、350℃、450℃) are deposited on 316L stainless steel and single crystal silicon by Multi -Arcion plating technique. Microstructures, mechanical performance and tribological performances in ambient air and water are systematically investigated by XRD, XPS, SEM, nano-indentation and ball-on-disc tribol-meter. The results show that the hardness and modulus increase with the increasing of deposition temperature and reach theclimax with deposition temperature at 450 ℃ and the maximum value at about 24 Gpa and 354 Gpa, respectively. Both the friction coefficients and wear rates of CrCNcoatings in ambient air and water tent to decrease after increasing first and reach the bottom with deposition temperature at 350 ℃. The friction coefficient in ambient airand water are about 0.38 and 0.23, the maximum value of wear rate in ambient air and water are about 1.717 1×10-6mm3/N▪m and 9.529 7×10-7mm3/N▪m, respectively. Meanwhile, the friction coefficients and wear rates of CrCN coatings in water are lower than that in ambient air, which is attributed to the good lubrication of waterduring the friction.
  • [1]
    Meicke S,Paasch R,Seawater lubricated polymer journal bearings for use in wave energy converters[J]. Renewable Energy,2012,39: 463-470.
    [2]
    Wang Q,Zhou F,Wang X,et al. Comparison of tribological prop­erties of CrN,TiCN and TiAlN coatings sliding against SiC balls in water[J]. Applied Surface Science,2011,257: 7813-7820. doi: 10.1016/j.apsusc.2011.04.035
    [3]
    Wang C T,Gao N,Gee Mark G,et al. Processing of an ultrafine­grained titanium by high -pressure torsion: An evaluation of the wear properties with and without a TiN coating[J]. Journal of Me­chanical Behavior of Biomedical Material,2013,17 : 166-175. doi: 10.1016/j.jmbbm.2012.08.018
    [4]
    Deng B,Tao Y,Guo D L. Effects of vanadium ion implantation on microstructure, mechanical and tribological properties of TiN coatings[J]. Applied Surface Science,2012,258(22): 9080-9086. doi: 10.1016/j.apsusc.2012.06.001
    [5]
    Ono T,Uemurn M,Yatsuzuka M. Adhesion improvement of TiN film on tool steel by a hybrid process of unbalanced magnetron sputtering and plasma-based ion implantation[J]. Nuclear Instru­ments and Methods in Physics Research Section B: Beam Inter­actions with Material and Atoms,2007,257(1/2): 786-789. http://cn.bing.com/academic/profile?id=1986961228&encoded=0&v=paper_preview&mkt=zh-cn
    [6]
    李国亮,肖厚群,揭晓华,等.液相脉冲放电制备TiCN多元陶瓷涂 层[J].中国表面工程,2013, 262(2): 82-86. http://www.cnki.com.cn/Article/CJFDTOTAL-BMGC201302022.htm
    [7]
    古柏林,刘捍卫,朱旻昊,等.TiN/Ti复合涂层高温微动磨损特性 研究[J].中国表面工程,2010, 23(3): 89-94. http://www.cnki.com.cn/Article/CJFDTOTAL-BMGC201003024.htm
    [8]
    龚才,代明江,陈明安,等.基体材料对TiN薄膜表面液滴及薄膜结合力的影响[J].中国表面工程,2013, 26(1): 27-33. http://www.cnki.com.cn/Article/CJFDTOTAL-BMGC201301008.htm
    [9]
    付英英,李红轩,吉利,等.CrN和C.A1N薄膜的微观结构及在不同 介质中的摩擦学性能[J].中国表面工程,2012, 25(6): 34-41. http://www.cnki.com.cn/Article/CJFDTOTAL-BMGC201206009.htm
    [10]
    叶育伟,陈颢,王永欣,等.316L不锈钢表面沉积C.C/薄膜的 结构及性能研究[J].有色金属科学与工程,2014, 5(4): 49-54.
    [11]
    叶育伟,陈颢,王永欣,等.不同过渡层对C.C/涂层性能影响[J]. 有色金属科学与工程,2014,5(6):61-66.
    [12]
    Wang Q Z,Zhou F,Ding X D,et al. Microstructure and water- lubricated friction and wear properties of CrN (C) coatings with different carbon contents[J]. Applied Surface Science,2013,268: 579-587. doi: 10.1016/j.apsusc.2013.01.027
    [13]
    Warcholinski B, Gilewicz A. Effect of substrate bias voltage on the properties of CrCN and CrN coatings deposited by cathodic arc evaporation[J]. Vacuum,2013,90: 145-150. doi: 10.1016/j.vacuum.2012.04.039
    [14]
    Hu P F,Jiang B. Study on tribological property of CrCN coating based on magnetron sputtering plating technique[J]. Vacuum,2011,85: 994-998. doi: 10.1016/j.vacuum.2011.02.007
    [15]
    Zhang S,Bui X L,Fu Y.Megnetron sputtered hard a-C coatings of very high toughness[J]. Surface and Coatings Technology,2003, 167: 137-142. doi: 10.1016/S0257-8972(02)00900-3
    [16]
    Choo J H,Spikes H A,Ratoi M,et al. Friction reduction in low- load hydrodynamic lubrication with a hydrophobic surface[J]. Tri­bology International, 2007, 40: 154-159. doi: 10.1016/j.triboint.2005.09.006
    [17]
    Polcar T,Vitu T,Cvrcek L,et al. Effects of carbon content on the high temperature friction and wear of chromium carbonitride coatings[J]. Tribology International,2010,43: 1228-1233. doi: 10.1016/j.triboint.2009.12.010
    [18]
    Zhang H S,Endrino J L,Anders A. Comparative surface and nano-tribological characteristics of nanocomposite diamond-like carbon thin films doped by silver[J|. Applied Surface Science,2008, 255: 2551-2556. doi: 10.1016/j.apsusc.2008.07.193
    [19]
    胡树兵,李志章,催崑.过渡层对TiN涂层结合力的影响[J].材料保护,2001,34(9): 1-3.
  • Related Articles

    [1]GUO Junhua, DING Tianran, LI Peiyan, SUN Yixiang, LIU Jie, ZHONG Sujuan, ZHANG Ting’an. Research progress in strengthening the heat transfer efficiency of magnesium smelting[J]. Nonferrous Metals Science and Engineering, 2023, 14(6): 756-763. DOI: 10.13264/j.cnki.ysjskx.2023.06.002
    [2]CAO Caifang, PANG Zhensheng, YUAN Zhuangzhuang, WANG Ruixiang, NIE Huaping, LI Laichao. Study on the decomposition of spent SCR catalyst by Na2CO3-NaCl mixed roasting method[J]. Nonferrous Metals Science and Engineering, 2021, 12(3): 63-69. DOI: 10.13264/j.cnki.ysjskx.2021.03.008
    [3]OUYANG Kun, DOU Zhihe, ZHANG Ting'an, LIU Yan. The desulfurization process of lead and zinc mixed concentrate with oxygen[J]. Nonferrous Metals Science and Engineering, 2020, 11(2): 1-6. DOI: 10.13264/j.cnki.ysjskx.2020.02.001
    [4]XIAO Jun, CHEN Daixiong, YANG Jianwen, QI Zhongxu, DONG Yanhong, ZENG Huiming. Separation tests of the lead-zinc-sulfur mixed concentrate in Fankou lead and zinc mine[J]. Nonferrous Metals Science and Engineering, 2015, (2): 104-109. DOI: 10.13264/j.cnki.ysjskx.2015.02.020
    [5]ZHONG Zhiqiang, ZHENG Haihua, OUYANG Shuilin, CHEN Han. Ball milling efficiency of heptahedron ball milling medium and its effects on alloy structure property[J]. Nonferrous Metals Science and Engineering, 2014, 5(3): 60-64. DOI: 10.13264/j.cnki.ysjskx.2014.03.011
    [6]CHEN Ming-xing. The Practice of Processing Tantalum & Niobium[J]. Nonferrous Metals Science and Engineering, 2003, 17(2): 22-23.
    [7]DENG Zuo-guo, XU Ting-hua, YANG Feng-li. Optimization Study on the Extraction Separation Process of Mixed Light Rare Earth[J]. Nonferrous Metals Science and Engineering, 2003, 17(1): 29-31.
    [8]HU Jian-guo, MAO Shi-yi. The Way to Raise Grinding Efficiency[J]. Nonferrous Metals Science and Engineering, 2002, 16(2): 11-12,21.
    [9]WEN Hui-zhong. A study on preparing mixed RE metals by fluorides electrolysis[J]. Nonferrous Metals Science and Engineering, 2001, 15(1): 27-30.
    [10]YU Guo-jing, LIN Guo-hong. A Research on the Mixed Filling Materials in Sectional Filling Mining[J]. Nonferrous Metals Science and Engineering, 2000, 14(2): 8-11.
  • Cited by

    Periodical cited type(1)

    1. 贾东铭,陈乔,郭小载,谢庆明. 基于次声的滑坡监测预警技术研究进展. 科技创新与应用. 2023(14): 7-12+17 .

    Other cited types(1)

Catalog

    Article Metrics

    Article views (75) PDF downloads (3) Cited by(2)
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return