| Citation: |
CAI Zhiyong, WEN Jing, WANG Richu, PENG Chaoqun. Application of surface modification of reinforcing phase in metal matrix composites with high thermal conductivity[J]. Nonferrous Metals Science and Engineering, 2024, 15(2): 237-255. DOI: 10.13264/j.cnki.ysjskx.2024.02.011
|
With the rapid development of electronic technology and the upgrading of electronic devices, the requirement for electronic packaging materials is getting higher than before. Metal matrix composites, especially aluminum and copper matrix composites have the characteristics of high thermal conductivity, low expansion, and high stability, which are electronic packaging materials with broad application prospects. However, diamond, graphene, silicon, and other reinforcements have poor wettability with the matrix, or have harmful interface reaction with the matrix at high temperature, which limits the development and application of metal matrix composites with the high thermal conductivity. This paper briefly described the research progress of interface of metal matrix composites, and proposed several methods to improve the interface bonding based on the factors that affect the interface bonding of metal matrix composites. Surface modification of reinforcement is one of the most important ways to improve the interface of metal matrix composites. The common technologies include magnetron sputtering, chemical vapor deposition, sol-gel and electroless plating. Finally, the application of surface modification of reinforcement in metal matrix composites with high thermal conductivity was analyzed and prospected.
| [1] |
HAO Y, XIANG S, HAN G, et al. Recent progress of integrated circuits and optoelectronic chips[J]. Science China Information Sciences, 2021, 64(10): 103-135.
|
| [2] |
邹良华. IC封装的研究综述及经济价值分析[J]. 数码世界, 2021(6): 62-63.
|
| [3] |
许春停, 郭祊鹤, 张辉, 等. 喷射沉积Al-12Si-0.6Mg合金的微观组织与性能[J]. 有色金属科学与工程, 2021, 12(2): 43-49.
|
| [4] |
张文毓. 电子封装材料的研究与应用[J]. 上海电气技术, 2017, 10(2): 72-77.
|
| [5] |
JU H, LIU S. Damage degree analysis of storage failure modes for plastic encapsulated microelectronic devices[J]. Journal of Physics: Conference Series, 2021, 2132(1): 012048.
|
| [6] |
曾婧, 彭超群, 王日初, 等. 电子封装用金属基复合材料的研究进展[J]. 中国有色金属学报, 2015, 25(12): 3255-3270.
|
| [7] |
赵玉涛, 戴起勋, 陈刚. 金属基复合材料[M]. 北京: 机械工业出版社, 2007.
|
| [8] |
陈贞睿, 刘超, 谢炎崇, 等. 高导热金属基复合材料的制备与研究进展[J]. 粉末冶金技术, 2022, 40(1): 40-52.
|
| [9] |
TONG X C. Advanced materials for thermal management of electronic packaging[M]. New York: Springer New York, 2011.
|
| [10] |
周朗牙, 王日初, 王小锋, 等. SiCp/2014Al复合材料的热变形行为及本构模型[J]. 有色金属科学与工程, 2021, 12(4): 66-74.
|
| [11] |
YOSHINORI N. Introduction to metal matrix composites[M]. Tokyo: Springer Tokyo, 2013.
|
| [12] |
CHOI Y B, GEN S, KAZUHIRO M, et al. Low pressure casting process of FeCrSi/A366.0 alloy composites and their characterization[J]. Key Engineering Materials, 2006, 45(326/327/328): 1741-1744.
|
| [13] |
FUYAMA N, AOKI Y, UESUGI T, et al. Construction of constitutive equation for elevated temperature deformation in FeCrSi fiber-reinforced Al Alloy Composites[J]. Journal of the Society of Materials Science Japan, 2018, 67(11): 1000-1005.
|
| [14] |
马安博. 铝基复合材料的研究进展[J]. 化学与粘合, 2018, 40(2): 138-140.
|
| [15] |
张育铭. 碳纤维增强铝基复合材料制备及性能研究[D]. 兰州: 兰州理工大学, 2016.
|
| [16] |
陈志平, 陈维平, 刘方方. 铸造铝基复合材料的研究进展[J]. 铸造设备与工艺, 2020(1): 42-46, 54.
|
| [17] |
蔡志勇, 王日初. 快速凝固铝硅合金电子封装材料[M]. 长沙: 中南大学出版社, 2016.
|
| [18] |
朱和国. 内生型铝基复合材料反应机制与性能[M]. 北京: 国防工业出版社, 2013.
|
| [19] |
李少斌, 黄焰, 李晓锋, 等. 陶瓷颗粒增强铜基复合材料的研究进展[J]. 军民两用技术与产品, 2016(2): 135-136.
|
| [20] |
吴泓, 王志法, 郑秋波, 等. 铜基电子封装复合材料的回顾与展望[J]. 中国钼业, 2006, 30(3): 30-32.
|
| [21] |
KORB G, KORÁB J, GROBOTH G. Thermal expansion behaviour of unidirectional carbon-fibre-reinforced copper-matrix composites[J]. Composites Part A: Applied Science and Manufacturing, 1998, 29(12): 1563-1567.
|
| [22] |
LEI L, TANG Y, ZHAO H, et al. Fabrication and properties of short carbon fibers reinforced copper matrix composites[J]. Journal of Materials Science, 2008, 43(3): 974-979.
|
| [23] |
DATTA S K, TEWARI S N, GATICA J E, et al. Copper alloy-impregnated carbon-carbon hybrid composites for electronic packaging applications[J]. Metallurgical and Materials Transactions A, 1999, 30(1): 175-181.
|
| [24] |
AMALU N I, OKORIE B A, UGWUOKE J C, et al. Electrical conductivity of spark plasma sintered W-Cu and Mo-Cu composites for electrical contact applications[J]. Journal of Minerals and Materials Characterization and Engineering, 2021, 9(1): 48-60.
|
| [25] |
SOMANI N, SHARMA N, SHARMA A, et al. Fabrication of Cu-SiC composites using powder metallurgy technique[J]. Materials Today: Proceedings, 2018, 5(14): 28136-28141.
|
| [26] |
FATOBA O S, POPOOLA O, POPOOLA A P I. The effects of silicon carbide reinforcement on the properties of Cu/SiCp composites[J]. Silicon, 2015, 7(4): 351-356.
|
| [27] |
YUANG-FA L, SHENG-LONG L. Effects of Al additive on the mechanical and physical properties of silicon reinforced copper matrix composites[J]. Scripta Materialia, 1999, 41(7): 773-778.
|
| [28] |
LEVIN L, ATZMON Z, KATSMAN A, et al. The mechanisms of phase transformation in diffusion couples of the Cu-Si system[J]. Materials Chemistry and Physics, 1995, 40(1): 56-61.
|
| [29] |
ERBIL H Y. Surface chemistry of solid and liquid interfaces[M]. Oxford: Blackwell Publishing Ltd, 2006.
|
| [30] |
HUANG Z. New equations of wetting[J]. Philosophical Magazine Letters, 2020, 100(4): 181-188.
|
| [31] |
王宁, 严红燕, 李慧, 等. 金属陶瓷润湿性影响因素的研究进展[J]. 特种铸造及有色合金, 2019, 39(12): 1315-1319.
|
| [32] |
黄岳山, 李文方, 蒙继龙, 等. 液态浸渗法制备Al2O3-SiO2纤维/Al-Si复合材[J]. 材料开发与应用, 1998, 13(2): 26-30.
|
| [33] |
CHEN J, GU M, PAN F. Reactive wetting of a metal/ceramic system[J]. Journal of Materials Research, 2002, 17(4): 911-917.
|
| [34] |
BAI G, LI N, WANG X, et al. High thermal conductivity of Cu-B/diamond composites prepared by gas pressure infiltration[J]. Journal of Alloys and Compounds, 2018, 735: 1648-1653.
|
| [35] |
CHU K, WANG F, LI Y B, et al. Interface and mechanical/thermal properties of graphene/copper composite with Mo2C nanoparticles grown on graphene[J]. Composites Part A, 2018, 109: 267-279.
|
| [36] |
王靖, 刘锦平, 孙科, 等. 烧结温度对石墨/铜复合材料微观组织与性能的影响[J]. 有色金属科学与工程, 2020, 11(1): 51-59.
|
| [37] |
刘桂武, 乔冠军, 卢天健, 等. Ni-56Si合金对SiC陶瓷的润湿和铺展[J]. 硅酸盐学报, 2010, 38(8): 1509-1513.
|
| [38] |
MURRAY J L, MCALISTER A J. The Al-Si (Aluminum-Silicon) system[J]. Bulletin of Alloy Phase Diagrams, 1984, 5(1): 74-84.
|
| [39] |
LIU J, XIU Z, LIANG X, et al. Microstructure and properties of Sip/Al–20wt% Si composite prepared by hot-pressed sintering technology[J]. Journal of Materials Science, 2014, 49(3): 1368-1375.
|
| [40] |
李树杰, 张利. SiC基材料自身及其与金属的连接[J]. 粉末冶金技术, 2004, 22(2): 91-97.
|
| [41] |
LIU G W, MUOLO M L, VALENZA F, et al. Survey on wetting of SiC by molten metals[J]. Ceramics International, 2010, 36(4): 1177-1188.
|
| [42] |
PROTSENKO P, GARANDET J P, VOYTOVYCH R, et al. Thermodynamics and kinetics of dissolutive wetting of Si by liquid Cu[J]. Acta Materialia, 2010, 58(20): 6565-6574.
|
| [43] |
OKAMOTO H. Cu-Si (copper-silicon)[J]. Journal of Phase Equilibria, 2002, 23(3): 281-282.
|
| [44] |
董翠鸽, 王日初, 彭超群, 等. SiCp/Al复合材料研究进展[J]. 中国有色金属学报, 2021, 31(11): 3161-3181.
|
| [45] |
JIA S Q, YANG F. High thermal conductive copper/diamond composites: state of the art[J]. Journal of Materials Science, 2021, 56(3): 2241-2274.
|
| [46] |
LI X H,YAN S J,CHEN X, et al. Microstructure and mechanical properties of graphene-reinforced copper matrix composites prepared by in-situ CVD, ball-milling, and spark plasma sintering[J]. Journal of Alloys and Compounds, 2020, 834: 155182.
|
| [47] |
CHU K, JIA C. Enhanced strength in bulk graphene-copper composites[J]. Physica Status Solidi, 2014, 211(1): 184-190.
|
| [48] |
CHEN F, YING J, WANG Y, et al. Effects of graphene content on the microstructure and properties of copper matrix composites[J]. Carbon, 2016, 96: 836-842.
|
| [49] |
王春江, 王强, 赫冀成. 液态金属铸造法制备金属基复合材料的研究现状[J]. 材料导报, 2005, 19(5): 53-57.
|
| [50] |
张士宪, 赵晓萍, 李运刚. 金属基表面复合材料的制备方法及研究现状[J]. 热加工工艺, 2017, 46(8): 6-10.
|
| [51] |
邱博, 邢书明, 董琦. 颗粒增强金属基复合材料界面结合强度的表征：理论模型、有限元模拟和实验测试[J]. 材料导报, 2019, 33(5): 862-870.
|
| [52] |
MONAZZAH A H, POURALIAKBAR H, JANDAGHI M R, et al. Influence of interfacial adhesion on the damage tolerance of Al6061/SiCp laminated composites[J]. Ceramics International, 2017, 43(2): 2632-2643.
|
| [53] |
KANG G, SHAO X, GUO S. Effect of interfacial bonding on uniaxial ratchetting of SiCp/6061Al composites: Finite element analysis with 2-D and 3-D unit cells[J]. Materials Science and Engineering, 2008, 487(1/2): 431-444.
|
| [54] |
姜芳, 宁建国. 有界面脱粘时颗粒增强金属基复合材料的弹塑性性能分析[J]. 材料工程, 2006(增刊1): 366-369, 373.
|
| [55] |
崔春翔, 吴人洁, 王浩伟. 金属基复合材料界面特征与力学性能[J]. 宇航材料工艺, 1997, 27(1): 1-6.
|
| [56] |
董应虎, 周贤良, 华小珍. 孔隙率对Mo/Cu复合材料热物理性能的影响[J]. 热加工工艺, 2008, 37(16): 1-3, 6.
|
| [57] |
牛宏伟, 文敏, 张帅. 考虑界面层和孔隙的SiCf/SiCm复合材料热膨胀性能研究[J]. 功能材料, 2020, 51(4): 4101-4108.
|
| [58] |
邓世岐. 炭/铜合金体系的界面行为和炭纤维织物增强铜基复合材料制备[D]. 太原: 太原理工大学, 2016.
|
| [59] |
ERVIN V J, KLETT J W, MUNDT C M. Estimation of the thermal conductivity of composites[J]. Journal of Materials Science, 1999, 34(14): 3545-3553.
|
| [60] |
DAVIS L C, ARTZ B E. Thermal conductivity of metal-matrix composites[J]. Journal of Applied Physics, 1995, 77(10): 4954-4960.
|
| [61] |
QIAN L, HE X B, REN S B, et al. Effect of titanium carbide coating on the microstructure and thermal conductivity of short graphite fiber/copper composites[J]. Journal of Materials Science, 2013, 48(17): 5810-5817.
|
| [62] |
蒋华义, 张亦翔, 梁爱国, 等. 材料表面润湿性的影响因素及预测模型[J]. 表面技术, 2018, 47(1): 60-65.
|
| [63] |
LAURENT V, CHATAIN D, CHATILLON C, et al. Wettability of monocrystalline alumina by aluminium between its melting point and 1273 K[J]. Acta Metallurgica, 1988, 36(7): 1797-1803.
|
| [64] |
WEN Z, ROBERT N. Surface roughness and contact angle[J]. Journal of Physical & Colloid Chemistry, 1949, 53(9): 1466-1467.
|
| [65] |
王德志, 张宇晴, 段柏华. 微波快速熔渗制备钼铜复合材料[J]. 有色金属科学与工程, 2018, 9(3): 11-16.
|
| [66] |
ANDREWS R M, MORTENSEN A. Lorentz-force-driven infiltration by aluminum[J]. Materials Science & Engineering A, 1991, 144(1/2): 165-168.
|
| [67] |
LI J G, COUDURIER L, EUSTATHOPOULOS N. Work of adhesion and contact-angle isotherm of binary alloys on ionocovalent oxides[J]. Journal of Materials Science, 1989, 24(3): 1109-1116.
|
| [68] |
孙科, 刘锦平, 王靖. 放电等离子烧结制备镍掺杂石墨-铜复合材料组织性能研究[J]. 有色金属科学与工程, 2020, 11(3): 65-72.
|
| [69] |
LI J G. Wettability of silicon carbide by liquid silver and binary silver-silicon alloy[J]. Materials Letters, 1994, 18(5/6): 291-298.
|
| [70] |
YANG W, CHEN G, WANG P, et al. Enhanced thermal conductivity in Diamond/Aluminum composites with tungsten coatings on diamond particles prepared by magnetron sputtering method[J]. Journal of Alloys and Compounds, 2017, 726: 623-631.
|
| [71] |
刘猛, 白书欣, 李顺, 等. 界面改性对SiCp/Cu复合材料热物理性能的影响[J]. 材料工程, 2016, 44(8): 11-16.
|
| [72] |
SUNDBERG G, PAUL P, SUNG C, et al. Identification and characterization of diffusion barriers for Cu/SiC systems[J]. Journal of Materials Science, 2005, 40(18): 5115-5119.
|
| [73] |
郑水林. 无机粉体表面改性技术发展现状与趋势[J]. 无机盐工业, 2011, 43(5): 1-6.
|
| [74] |
郝晓亮. 磁控溅射镀膜的原理与故障分析[J]. 电子工业专用设备, 2013, 42(6): 57-60.
|
| [75] |
陈秀华, 王莉红, 项金钟, 等. 超大规模集成电路铜布线扩散阻挡层TaN薄膜的制备研究[J]. 功能材料, 2007, 38(5): 750-752.
|
| [76] |
MAJUMDER P, TAKOUDIS C G. Investigation on the diffusion barrier properties of sputtered Mo/W-N thin films in Cu interconnects[J]. Appl Phys Lett, 2007, 91(16): 162108.
|
| [77] |
IVANOV E, RIO E D. Preparation of W-W 2 B composites from W-BN powders and properties of W-B-N barrier for copper metallization[J]. International Journal of Refractory Metals & Hard Materials, 2018, 72: 223-227.
|
| [78] |
SUN L, YUAN G, GAO L, et al. Chemical vapour deposition[J]. Nature Reviews Methods Primers, 2021, 1(5): 1-20.
|
| [79] |
GOKCE O H, AMIN S, RAVINDRA N M, et al. Effects of annealing on X-ray-amorphous CVD W-Si-N barrier layer materials[J]. Thin Solid Films, 1999, 353(1): 149-156.
|
| [80] |
CHENG H E, LEE W J, HSU C M. The effect of deposition temperature on the properties of TiN diffusion barriers prepared by atomic layer chemical vapor deposition[J]. Thin Solid Films, 2005, 485(1): 59-65.
|
| [81] |
管振宏, 于镇洋, 乔志军, 等. 化学气相沉积法制备原位生长三维石墨烯/铜基复合材料[J]. 材料科学与工程学报, 2021, 39(4): 575-579.
|
| [82] |
刘莎, 徐源来, 赵培, 等. 沉积温度对化学气相沉积法制备铜薄膜性质的影响[J]. 真空科学与技术学报, 2021, 41(7): 640-647.
|
| [83] |
刘涛, 赖中元, 李小成, 等. 二氧化钛涂层改性锌负极及其在水系锌离子电池中的应用[J]. 有色金属科学与工程, 2023, 14(1): 51-56.
|
| [84] |
TAN Z, LI Z, FAN G, et al. Enhanced thermal conductivity in diamond/aluminum composites with a tungsten interface nanolayer[J]. Materials & Design, 2013, 47: 160-166.
|
| [85] |
程少辉. 金刚石表面金属化处理[D]. 郑州: 郑州大学, 2014.
|
| [86] |
CAI H, TONG D B, WANG Y P, et al. Novel Cu/Si composites: A sol-gel-derived Al2O3 film as barrier to control interfacial reaction[J]. Journal of Materials Research, 2010, 25(11): 2238-2244.
|
| [87] |
汪涛, 蒋明慧, 张慧峰, 等. 溶胶凝胶法制备氧化石墨烯/氧化铝复合材料[J]. 人工晶体学报, 2017, 46(11): 2295-2298.
|
| [88] |
卢建红, 余柳丝, 范金龙, 等. EDTA/THPED二元络合体系化学镀铜的沉积动力学分析[J]. 有色金属科学与工程, 2022, 13(6): 42-49.
|
| [89] |
刘静萍, 葛圣松, 孙宏飞, 等. 化学镀的国内外研究现状及展望[J]. 山东机械, 2001(2): 2-5.
|
| [90] |
杨斌, 刘敬萱, 齐亮, 等. 碳纤维表面镀镍工艺研究[J]. 有色金属科学与工程, 2016, 7(5): 53-58.
|
| [91] |
姚丹, 李成威, 韩凯新, 等. 人造金刚石表面化学镀W/Ni-P层的工艺优选及镀层质量[J]. 材料保护, 2015, 48(1): 30-32, 56.
|
| [92] |
汤英童, 杨长城. 金刚石粉表面化学镀镍工艺改进及镀层显微分析[J]. 光学与光电技术, 2021, 19(5): 75-81.
|
| [93] |
刘世敏, 李国彬. 金刚石表面化学镀Ni-P复合层的显微分析[J]. 金刚石与磨料磨具工程, 2008, 28(3): 58-61, 65.
|
| [94] |
LÜ P H, WANG X F, DONG C G, et al. Preparation and characterization of different surface modified SiCp reinforced Al-matrix composites[J]. Journal of Central South University, 2020, 27(9): 2567-2577.
|
| [95] |
DONG C, WANG R, GUO S. Microstructures and mechanical properties of Cu-coated SiC particles reinforced AZ61 alloy composites[J]. Coatings, 2019, 9(12): 1854-1863.
|
| [96] |
王艳辉, 王明智, 臧建兵. 金刚石真空微蒸发镀钛技术新进展及应用[J]. 金刚石与磨料磨具工程, 1998, 18(3): 2-6.
|
| [97] |
CHUPRINA V G, VOLK G P. Special features of formation of molybdenum coatings on diamond with the spatial distribution of reagents[J]. Soviet Powder Metallurgy and Metal Ceramics, 1988, 27(4): 311-314.
|
| [98] |
汤小文. 金刚石的盐浴镀钨[J]. 机械工程材料, 1998, 22(6): 31-32.
|
| [99] |
温国栋. 金刚石表面改性单金属镀层的研究进展[J]. 热加工工艺, 2019, 48(16): 18-21.
|
| [100] |
KANG Q, HE X, REN S, et al. Effect of molybdenum carbide intermediate layers on thermal properties of copper-diamond composites[J]. Journal of Alloys and Compounds, 2013, 576: 380-385.
|
| [101] |
郑水林. 影响粉体表面改性效果的主要因素[J]. 中国非金属矿工业导刊, 2003(1): 13-16.
|
| [1] | ZHANG Xiaoqing, JIANG Qingwei, ZHANG Shoujian, LIU Bowen, WANG Honggang, YAN Guangmao. Research progress of high-strength and high-conductivity graphene reinforced copper matrix composites[J]. Nonferrous Metals Science and Engineering, 2023, 14(5): 641-650. DOI: 10.13264/j.cnki.ysjskx.2023.05.006 |
| [2] | LI Liqing, ZHOU Run, LONG Huiting, KONG Huimin, ZOU Laixi, LUO Xianping, SHAO Yunan, YANG Guofei. Surface modification mechanism of magnesium hydroxide (101) based on density functional theory[J]. Nonferrous Metals Science and Engineering, 2023, 14(4): 447-453. DOI: 10.13264/j.cnki.ysjskx.2023.04.001 |
| [3] | LI Xingpeng, SHU Qing. Preparation, characterization of Lewis acidic solid acid catalyst Ce-Ag-PW and its catalytic application in biodiesel production via esterification[J]. Nonferrous Metals Science and Engineering, 2020, 11(2): 42-50. DOI: 10.13264/j.cnki.ysjskx.2020.02.006 |
| [4] | WANG Shuhong, LIU Xin, KONG Bin, LU Jiawei, LI Hong, LIU Liequan, WANG Jinjin, CHEN Juan, HUANG Weiya. Synthesis of CeO2/Bi2MoO6 nanocomposites and their enhanced photocatalytic degradation performance[J]. Nonferrous Metals Science and Engineering, 2019, 10(2): 68-76. DOI: 10.13264/j.cnki.ysjskx.2019.02.010 |
| [5] | LIU Wenyang, ZHANG Jianbo, WU Shanjiang, HU Meijun, CHEN Tingting, GUO Lili. Effects of Si on friction properties of Ti3SiC2/Al composites[J]. Nonferrous Metals Science and Engineering, 2017, 8(5): 89-94. DOI: 0.13264/j.cnki.ysjskx.2017.05.013 |
| [6] | LIN Shipeng, LIU Jinyan, JI Yanli. Research status of CNTs reinforced aluminum matrix composites[J]. Nonferrous Metals Science and Engineering, 2017, 8(2): 57-62. DOI: 10.13264/j.cnki.ysjskx.2017.02.010 |
| [7] | XIONG Changshi, CHEN Yunnen, DAI Zhenpeng. Modification of spent grains to improve acid turquoise blue A adsorption from wastewater[J]. Nonferrous Metals Science and Engineering, 2015, 6(6): 116-120. DOI: 10.13264/j.cnki.ysjskx.2015.06.021 |
| [8] | XU Bingsheng, WU Hu, HAN Lin, CHEN Junwei, YUAN Zhangfu. Simulation analysis on the surface morphology of Sn-3.0Ag-0.5Cu melting on the inclined Cu substrate[J]. Nonferrous Metals Science and Engineering, 2014, 5(4): 7-12. DOI: 10.13264/j.cnki.ysjskx.2014.04.002 |
| [9] | CHEN Hao, ZHU Song, YANG Jian-gao, CHEN Yi-sheng. Present Situation on Research of Rare Earth in Materials Surface Engineering[J]. Nonferrous Metals Science and Engineering, 2009, 23(3): 38-41. |
| [10] | LI Pei-zhi, ZHONG Sheng-wen, MEI Jia, LI Yan, HU Yang, LIU Qing-guo. The Researches on Surface Modification of Lithium Manganese Oxide Spinel and Latest Progresses[J]. Nonferrous Metals Science and Engineering, 2005, 19(2): 38-41. |
Supported by: Beijing Renhe Information Technology Co., Ltd. 
DownLoad: